200MHz bandwidth portable scopes with dual channels, colored display, high bandwidth and sample rate under matchless price worldwide; Advanced Functionalities include automatic measurements, advanced triggering modes, record length. Bring extraordinary user-friendliness and measurement accuracy for debug, design, education, quality control, training, manufacturing test across various industries. Desirable functionalities exceed industry standards and cater to your normal or potential demands.
Bandwidth：200 MHz
Real-time Sample Rate：1GSa/s
Equivalent Sample Rate：25GSa/s
Record Length(Sample Points) ： Single-channel: Maximum 1M;
Dual-channel: Maximum 512K (4K,16K,40K optional)
SEC/DIV Range： 4nS/div-40S/div (in a 2, 4, 8 sequence)
Delay Time Accuracy： 500ps
-------------------------------------------------------------------------------------------------------------------------------------------------------------------
u Vertical
A/D Converter： 8-bit resolution, each channel sampled simultaneously
VOLTS/DIV Range： 2mV/div～5V/div at input BNC
Position Range： ±50V(5V/div),±40V(2V/div～500mV/div),2V(200mV/div～50mV/div)±400mV(20mV/div～
2mV/div)
Bandwidth Limit： 20MHz
Rise Time at BNC： ≤ 1.7ns
DC Gain Accuracy： ±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div
±3% for Sample or Average acquisition mode, 5V/div to 10mV/div
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
u Trigger
"Trigger Sensitivity(Edge Trigger Type)" ：DC: CH1/CH2(Typical) 1div from DC to
10MHz;1.5div from 10MHz to Full
EXT（Typical） 200mV from DC to 40MHz
EXT/5（Typical） 1V from DC to 40MHz
AC: Attenuates signals below 10Hz
HF Reject: Attenuates signals above 80kHz
LF Reject: Attenuates signals below 150kHz
Noise Reject: Reduces trigger sensitivity
Trigger Level Range： CH1,CH2: ±8 divisions from center of screen
EXT: ±1.2V
EXT/5: ±6V
"Trigger Level Accuracy,typical (Accuracy is for signals having rise and fall times ≥20ns)" ：
CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen)
EXT: ±(6% of setting + 40mV)
EXT/5: ±(6% of setting + 200mV)
Holdoff Range： 100ns-10s
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
u Trigger Type
Edge： Trigger on the rising or falling edge
Pulse Width： Trigger (when >,<,=,≠) on positive or negative pulses Pulse Width Range: 20ns-10s
Video： Trigger on an NTSC, PAL, or SECAM standard video signal Line Range: 1-525 (NTSC),
1-625 (PAL/SECAM)
Slope： Trigger (when >,<,=,≠) on a positive or negative slope ；Set Time: 20ns–10s
Overtime： From the rising or falling edge；Set Time: 20-10s
Alternate： Internal trigger on edge, pulse width, video or slope
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
u Measurement
Cursors: Manual: The difference between voltage cursors △V; the difference between time cursors
△T; 1/△T calculated by Hz.
Tracing: The voltage and time at a waveform point
Automatic: Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width,
Negative Width
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
u Display
Type：: Right angle 7"TFT 16-digit color LCD
Resolution： 800*480 dots
Contrast： 16 gears, with the progress bar to show adjustment
Interface： USB host and USB slave
|
